DAZZLEAF DAZZii BOXX 510 VV Batetry

DAZZLEAF DAZZii BOXX 510 Cartridge Stealth VV 650mAh Preheat Battery

DAZii BOXX designed to be as discreet as possible so that you can stealthily enjoy your favorite liquid.

Four voltage levels can be adjusted by auto-puff or bottom power button. The powerful 650mAh battery and Type-C fast charge allows you to enjoy a long vape without worrying about running out of charge!

DAZZii BOXX is compatible with most 510 cartridges up to 2ml

Four variable voltage settings, preheat mode, LED indicator light, short circuit/overcharge protection

DAZZii BOXX is available in 10 colors to suit your choice

Black／Tangie／Happy Green／White & Black／Paradise Blue／Purple Haze／Mad Skull／Green Splash／Black Clouds／Go Stoner(Rasta)

Specification

• 510 Cartridge Stealth VV 650mAh Preheat Battery Auto Puff/Power Button
• Compact pocket size: 42 x 18 x 84.5 mm
• Weight: 46g
• Cartridge size: 14mm x 60mm (fits most 0.5-2ml cartridges)
• 4 voltage settings: 2.4V Blue / 3.0V Green / 3.6V White / 4.2V Red
• Preheat function: 2.0V, 15 sec. preheat
• Automatically cuts off after 20 seconds of use. Automatic power off after 20 minutes.
• Convenient removable magnetic bottom with power button
• Type-C charging
• Cartridges sold separately.

Quick Start Guide

Charge the battery for 1 hour before first use.

Remove the magnetic bottom; attach a 510-standard cartridge tightly.

Auto puff function

5 quick puffs to power on, 2 quick puffs to preheat mode, 3 quick puffs to set voltage

Power button function

Quickly press the power button 5 times to turn on/off. Quickly press the power button 3 times to set the voltage. Quickly press the power button twice to enter preheat mode.

Preheat

Two quick puffs activate the preheat function. Two quick presses of the power button on the bottom also activates the preheat function. Preheat lasts for 15 seconds at a voltage of 2.0V. In the preheat mode, four LED lights flash slowly and a single press of the power button or a single puff stops the preheat.

Normal use

Vape can be done with both auto-puff and power button. Guide bar and sensor light up. The sensor does not light up in preheat mode.

Battery and Charging

When the remaining battery charge falls below 30%, the red light flashes 5 times.

Charging: Red light

Full charge: Green light

Low Battery: The red light flashes 8 times and the device turns off completely.

Battery life/Cartridge protection

After 10 seconds of continuous use, the red light flashes 4 times, the auto cut is activated, the heating (not the power) is turned off, and it works again by pressing or puffing the button.

Protection function

Short-circuit protection: If a short circuit is detected and the red light flashes 10 times, the device stops immediately.

Overcharge protection: When the battery is fully charged, it stops charging to prevent overcharging.

Overheat protection: If the unit continues to heat up for 15 seconds, it will pause for approximately 3 seconds. During this time, the indicator light on the bottom will flash 5 times.

Usage

Make sure the bottom magnetic connector is properly connected. If the bottom connector is not connected, the battery will not charge.

Connect the USB-C cable to the charger. The red light will flash when the battery is connected to the charger.

The battery must be fully charged before first use. The LED indicator will turn green when the battery is fully charged.

Remove the magnetic connector at the bottom and attach a 510-standard cartridge tightly.

Attach the cartridge to the device and make sure the magnetic connector on the bottom is properly attached.

If the device is turned off, press the power button five times to turn it on.

Press the button on the bottom 3 times or puff 3 times to change the voltage.

After two puffs, preheat begins. The preheat time is 15 seconds at a voltage of 2.0 V, after which it switches to the previously selected voltage.

It is activated by puffing or pressing the power button.

Cleaning

Remove the battery cover.

Wipe the outside and inside of the bottom magnetic connector with an alcohol pad. Use an alcohol swab to wipe off excess liquid and dirt from the 510 threads.

Clean the internal airflow with alcohol swabs.

Do not immerse any part of the device in the cleaning solution.

Make sure all parts are dry before use.